CENTRUM SZKOLENIOWE LIVOLTEK
PORADY
FAQ
CONTACT US
PORADY
- On-grid Inverter
What are the requirements for the inverter installation environment?
1）The installation carrier is sturdy and can bear the weight of the inverter for a long time.
2）Zaleca się, aby temperatura otoczenia oraz wentylacja urządzenia podczas instalacji była zgodna z wymaganiami w karcie katalogowej.
3）In order to ensure the best operation, it is necessary to avoid direct sunlight, rain and snow.
4）During operation, the case temperature will be relatively high, and please do not install the inverter in a place where it is easy to touch.
5）The space around the inverter must meet the installation, maintenance and heat dissipation requirements.
Jakie są wymagania dotyczące instalacji urządzenia?
Vertical installation/ Do not allow lying down/ Leaning back and inversion
How to prevent incorrect or misconnected DC cables from being crimped?
1）Do a good job of line marking to reduce the probability of errors
2）Before connecting to the inverter, use a multimeter to measure the input voltage of the component on the positive and negative sides to ensure that the polarity is correct and does not exceed the maximum input voltage.
3）Do zaciskania złączy fotowoltaicznych stosuj specjalne narzędzia.
4）If conditions permit, you can use an infrared thermal imager or a spot temperature gun to confirm the connection point temperature after grid-connected power generation.
How to ensure the waterproofness of the machine?
1）Uszczelnij przepust kablowy
2）Zaplombuj i uszczelnij niewykorzystywane porty
3）Pokrywę wejścia kablowego solidnie i szczelnie dokręć
4）Pamiętaj o dokręceniu nakrętki uszczelniającej dławika terminala
5）Pozostałe porty uszczelnij dołączoną do zestawu wodoodporną uszczelką
What are the reasons for the low power generation of the machine?
1）Słabe promieniowanie słoneczne
2） Ambient Temperature
3）Zła orientacja modułów fotowoltaicznych
4）Zły odstęp między modułami PV
5）Złe nachylenie modułów fotowoltaicznych
6）Zapylenie, bądź zabrudzenie modułów PV
7）Brak kompatybilności komponentów
8）Niestabilność sieci
9）Awaria lub usterka
What causes the monitoring interruption?
1）Poor Wi-Fi signal
2）GPRS signal is not good
3）Problemy z konfiguracją routera
4）Awaria routera
5）Router jest przeciążony
6）Interfejs modułu jest poluzowany
7）Brak rozdzielenia częstotliwości sieci WiFi
8）Awaria modułu komunikacyjnego
9）Awaria falownika
- Energy Storage System
How to choose EPS mode?
There are 4 types of EPS modes, they are:
0 – Disable
1 – EPS without bypass：only in the case of power failure, EPS port will have voltage output (basically no standby power consumption)
2 – EPS with bypass：When there is power grid, EPS port will also have voltage output, and when power failure, EPS port voltage will need about 2s for output switch (low power standby power consumption).
3 – EPS z bypassem: Port EPS również dostarcza napięcie wyjściowe przy obecności sieci, a w przypadku zaniku zasilania przechodzi w tryb EPS z czasem przełączenia <20ms (wysoki pobór mocy w stanie czuwania)
What is needed to pay attention to for the first installation?
Po pierwszym zainstalowaniu baterii zaleca się jej wymuszone naładowanie (w celu kalibracji baterii).
- EV Charger
Inteligentna ładowarka EV zasilana fotowoltaiką
1）Podłączenie zasilania ładowarki EV należy zabezpieczyć RCBO 30 mA, typ A.
2）Domyślna nazwa Bluetooth ładowarki to AC – {ostatnie 6 cyfr SN}, a domyślne hasło to 111111.
3）Installation environment Requirements
-The installation position of charger shall not be close to dangerous positions such as water pipe, gas pipe and steam pipe.
-The charger shall not be installed in places with severe vibration or high temperature.
-The installation position of charger should not be set in low-lying places where it is easy to accumulate water or drip.
-It is recommended that the charger be installed in an environment with sunshade or umbrella.
-A certain space shall be reserved for the installation of charger to facilitate the inspection and maintenance of technicians.
4）Domyślna długość złącza do ładowania pojazdu wynosi 5 metrów, co wystarcza do codziennego ładowania. Specjalne wymagania dotyczące długości mogą być realizowane na zamówienie.
FAQ
- Grid-Tied Inverter
Q: Mój router działa w paśmie 5 GHz. Czy mogę go użyć do podłączenia falownika do sieci Wi-Fi?
Nie, obecnie wszystkie adaptery Wi-Fi obsługują połączenie 2.4G Hz.
Q. How can llimit the power feed to the grid?
A smart meter is required, and please set the value of limit in the app Settings-Feed in Limitation.
Q. My inverter had an alarm saying "PV over current", what should l do?
Solar panel power cannot be more than 150% of inverter rated power. For example, a 6KW on grid inverter can connect 9KW solar panels at maximum. Therefore, please check whether solar panels are over installed. Or please install 9KW solar panels on two MPPTs instead of one MPPT
Q. Why is the LED not lit up?
Dioda LED wyświetlacza falownika zapali się, gdy napięcie startowe DC osiągnie wartość napięcia rozruchowego. Wartość napięcia rozruchowego zależy od mocy falownika.
Q. Does the Wi-Fi stick support connecting to the Lan port?
Yes.
Q. Does the inverter support meterless operation?
Yes. The inverter is in non-meter mode by default.
Q. Dlaczego aplikacja podczas pracy systemu nie monitoruje domowego obciążenia?
Należy dodać inteligentny liczniki.
Q. If the user's home does not have a ground wire, can the inverter be used normally?
If the inverter is not grounded, an alarm will sound, but the alarm can be cleared through remote settings. However, it is recommended to connect a ground wire.
Q. How much electricity can a single-phase grid-connected machine generally generate?
It is calculated based on the actual power of the inverter and the light resources in the area. For example, 6kW is calculated based on 6-8 hours, which is approximately 35-50kWh.
Q. Does the inverter support the latest PV panels?
Single-phase supports 182 series photovoltaic panels, and three-phase supports 210 series photovoltaic panels.
Q. Can users monitor remotely without Internet access?
Zdalny monitoring nie jest możliwy bez połączenia sieciowego. Aby sprawdzić status pracy falownika na platformie zdalnej/telefonie, należy podłączyć się do WiFi lub skorzystać z monitoringu w trybie lokalnym
- Off-grid Inverter
Q. What batteries can be used ?
Livoltek off-grid inverter compatible
Lead-acid battery: water battery, gel battery.
Lithium battery: Livoltek self-developed lithium battery, Payne, Shuangdeng, Daqin and some other brands of battery.
Need to match the normal communication through the protocol.
Q. How can we upgrade firmware for off-grid inverters?
- There are four ways to upgrade.
1.Upgrade from the app after connecting the inverter with smart phone bluetooth.
2.Upgrade by U disk.
3.Upgrade from LCD screen.
4.Upgrade from Livoltek platform when the inverter is online.
Q. How many work modes are there for Livoltek off-grid inverters, and which one should l choose?
There are backup mode, economic mode and off-grid mode.
Backup mode is advisable for users who live in an area where power outages happen frequently.
Economic mode is advisable for users who have solar panels and the electricity is expensive.
Off grid mode is for no grid area users. This mode does not need to be set from the App.
Q. Why is there no power that goes to EPS appliances?
Please turn on the ON/OFF switch at the bottom of the off-grid system. If it is turned on, please connect off-grid with Bluetooth and check what fault is happening, or contact Livoltek technical support.
Q. Do l need to set parameters for batteries?
Lithium batteries do not need to set parameters because the inverter can communicate with BMS. However, for lead-acid batteries or lithium batteries with no BMS, parameters need to be set.
Q. There is a beep when the grid is out of power.
The beep sound can be turned off from App at Settings-Basic settings-EPS setup-Beep on EPS.
Q. Can the off-grid inverters work under no battery connected?
Yes, Livoltek off-grid inverter can work without battery connected. Please note this does not work when multiple off grid inverters are paralleled.
Q. Can the off-grid inverters work under no battery connected?
Yes, Livoltek off-grid inverter can work without a battery connected. Please note this does not work when multiple off-grid inverters are paralleled.
Q. Does the off-grid machine support GPRS?
No, only WiFi and Ethernet are supported.
Q. The power grid is unstable. Can the inverter output voltage normally?
Yes, when the grid voltage is lower than 170V, it will automatically switch to off-grid mode, powered by PV and battery.
Q. Does the off-grid machine support battery-free operation?
Yes, 48V5kW, 6kW, and 6.2kW off-grid machines all support battery-free operation.
Q. Does the off-grid machine support parallel operation?
Yes, 12 units can be connected in parallel for single-phase and 12 units can be connected in parallel for three-phase (up to 4 units per phase).
Q. What protection functions does the inverter have?
Supports overload protection, overvoltage protection, overcurrent and overfrequency protection, undervoltage protection, output short circuit protection, overtemperature protection, lightning protection and other protection measures.
Q. What scenarios are off-grid machines suitable for?
The protection level of the inverter is IP21, which is suitable for installation in indoor, attic, basement, garage and other scenarios.
Q. Does it support diesel generators?
Supports both automatic and manual diesel generators.
- Hybrid Inverter
Q. How many solar panels can linstall at maximum?
150% of rated power. For example, a 5KW hybrid inverter can connect 7.5KW solar panels at maximum.
Q. Where should the CT arrow point to?
Please point the arrow to the inverter side.
Q. ls an external breaker required for battery?
As long as the battery is Livoltek lithium battery, an external breaker is not required.
Q. My router is 5GHz. Can luse it to connect the inverter to my Wi-fi?
No, currently Wi-Fi dongle can only connect 2.4GHz networks.
Q. l can not find Hyper series inverters in Product Type when trying to add a device to a site
Please check whether the System Type of the site is Residential solar energy storage (ess) or not. If not, delete the site and create a new one and select Residential solar energy storage (ess) for System Type.
Q. Which mode shouldlchoose for inverter?
Self-use mode: Solar panels are installed with sufficient power for household appliances and extra power to feed batteries.
Back-up mode: Loadshedding happens frequently, needs batteries to feed appliances, especially after sunset.
Q. What does Discharge End SOC@Grid and SOC@EPs mean?
Discharge End SOC@Grid: this value works as a threshold to stop battery discharging when there is power coming from the grid.
Discharge End SOC@EPS: this value works as a threshold to stop battery discharging when there is no power coming from the grid.
Q. Can l set a timer for battery charging?
Yes, please open My Livoltek app, go to Setting, choose Basic Settings, in Work Mode select Self-Define and add timers. Users can use this mode to avoid charging at peak electricity prices.
Q. Can the inverter work under no battery connected?
Yes, Livoltek hybrid inverter can work without battery connected.
Q. When there is power from the qrid, why does EPS loads not have power?
Please open My Livoltek app, go to Setting tabs, choose Basic Settings and select UPS at EPS mode.
Q. Can the inverter only be connected to lithium batteries?
Not only one type of battery, the inverter can also be connected to batteries other than lithium batteries, such as lead-acid batteries, non-communication lithium batteries, etc.
Q. Does the inverter need a smart meter?
The factory default is that the meter is equipped with CT, but it can be selected according to the user’s on-site needs.
Q. Does the energy storage machine support 0 power feeding?
Yes, the Hyhrid energy storage machine supports 0 power feeding.
Q. Does the energy storage machine support parallel system?
Yes, it supports up to 2 parallel systems, but you need to consult with the sales staff in advance and purchase before placing an order.
Q. Does the energy storage machine have noise problems?
The energy storage machine is fanless and will not cause noise pollution.
Q. Can I check the working status of the energy storage machine on my mobile phone?
Tak, pobierz aplikację 'My Livoltek’, która obsługuje zarówno platformy Android, jak i Apple.
1. 1.Check some details and related settings via local Bluetooth;
2.Log in to the account remotely to check the working status of the inverter.”
Q. In what scenarios is the energy storage machine suitable for installation?
The protection level of the inverter is IP65, and it can be installed outdoors, in ventilated corridors, underground garages, and attics.
Q. What is the warranty policy for the inverter?
Usually the default warranty is 5 years. If you need to extend the warranty or increase the years, please contact the staff.
Q. Can the energy storage device be connected to a diesel generator?
Yes. We support both automatic and manual diesel engines.
Q. What are the advantages of energy storage machines?
They can reduce peak loads and fill valleys, realize power feeding, and reduce equipment costs.
- Energy Storage System
Q. Do l need to add a fuse to the battery?
It is not required because we have a DC isolator already added on the battery side.
Q. What is the current of the DC isolator on the battery?
It is 125A, 1.25 times rated power of battery.
Q. How long does the battery's cycle life?
6000 Cycles. (Test conditions: 0.2C Charging/Discharging, @25℃, 80% DoD, 60% EOL)
- EV Charger
Q. Livoltek A0070230E11,A0070230E12,A0110400E11,A0220400E11 are applicable to which types of connectors?
XXXXXXXXE11 is applicable to Type 2 connectors, and XXXXXXXXE12 is applicable to Type 1 connectors.
Q. Does the EV Charger work with any brand of inverter?
Currently, this EV Charger only communicates with Livoltek Hyper 5000 inverter.
Q. What is the password for the Bluetooth connection?
When users connect to Bluetooth for the first time, please enter password 111111 and connect to the last 8 digits of the EV Charger serial number. The next time, for the same phone, users do not need to enter the password.
Q. When l am trying to connect the EV Charger online, is it possible to use 5 GHz Wi-fi?
Please use 2.4 GHz Wi-Fi to connect EV Charger online. The network name should be the English alphabet and numbers.
Q. ls the grounding line required to be connected?
Yes, please connect the grounding line.